5.2.1 Warning:

5.2.2 Current to Passive Mode Configuration:

For multi-drop mode the current output must be configured as pas-

sive mode. Please disregard any other messages shown on HHT.

5.3 Configuration Data Review:

Before operating the transmitter make sure the configuration data

on the nameplate matches the application.

5.4 Configuration Verification:

Before the transmitter is ready for service, the configuration must be

checked to confirm the settings are configured for the application.

5.4.1 Process Variable:

There are two process variables in the 3100 Smart Pressure

Transmitter. The primary variable and temperature compensated SV

(Second Variable), the PV value outputs the 4~20mA analog value.

5.5 Basic Setup:

The correlation variable must be configured before operating the

transmitter.

5.5.1 Select Sensor Range:

The pressure range must be selected when ordering the pressure

transmitter.

5.5.2 Set Output Units:

Select from the following engineering units:

Volumetric Flow Unit -

CubicFeet/min, Gallons/min, Liters/min,

ImperialGallons/min, CubicMeter/hr, Ft/s, meters/s,

Gallons/s, mGallons/day, Liters/s, mLiters/day, CubicFeet/s,

CubicMeter/s, CubicMeter/day, ImperialGallons/hr,

ImperialGallons/day, NormalCubicMeter/hr, NormalLiter/hr,

StandardCubicFeet/min, CubicFeet/hr, CubicFeet/day,

CubicMeters/min, Barrels/s, Barrels/min, Barrels/hr,

Barrels/day, Gallons/hr, ImperialGallons/s, Liters/hr,

Gallons/day

Mass Flow -

Grams/s, Grams/min, Grams/hr, Kilograms/s,

Kilograms/min, Kilograms/hr, Kilograms/day,

MetricTons/min, MetricTons/hr, MetricTons/day, Pounds/s,

Pounds/min, Pounds/hr, Pounds/day, ShortTons/min,

ShortTons/hr, ShortTons/day, LongTons/hr, LongTons/day

Pressure -

kPa, mmH2O, InH2O, InHg, FtH2O, mmHg, psi, bar, mbar,

g/cm

, Kg/cm

, Pascals, MPa, torr, ATM

Miscellaneous -

Time -

Min, sec, hr, days

Mass -

Grams, kilograms, metric tons, pounds, short tons, long tons,

ounce

Volume -

Gallons, liters, imperial gallons, cubic meters, barrels,

bushels, cubic yards, cubic feet, cubic inches, bbl liq, normal

cubic meter, normal liter, standard cubic feet, hectoliters

5.5.3 4-20mA Configuration:

Set the Zero and Span for the 4~20mA analog output.

5.6 Detailed Setup:

5.6.1 Set Fail Mode:

When the sensor or microprocessor is not operating properly, the

transmitter will output 3.75mA or 21.75mA based on the Fail

Mode setting.

5.6.2 Set Dampening Time:

The Dampening Seconds value changes the response time of the

ransmitter to smooth out variations caused by rapid process

changes. Determine the appropriate dampening setting based on

the required response time, signal stability, and other require-

ments of your system.

The Dampening Seconds can be set from 0-60 seconds; the

default dampening value is 1.0 second.

5.7 Configuration of Information Variable:

5.7.1 Set Tag:

Tags are an easy way to classify transmitters in multi transmitter

application. Tags can use 8 words/numbers.

5.7.2 Set Messages:

When using several transmitters, the user can define each transmit-

ter by using 32 words/numbers. This message is saved in EEPROM.

5.8 Diagnostics and Service:

5.8.1 Loop Test:

The Loop Test verifies the output of the transmitter, the integrity of

the loop, and the operations of any recorders or similar devices

installed in the loop. The following procedures are required for a

loop test.

• Connect a reference meter to the transmitter.

• Select the Loop Test on the HHT and operate the Loop Test.

• Select current output (4mA/20mA/etc.)

• If the readings match, then the transmitter and the loop are

configured and functioning properly. If the readings do not

match, then you may have the current meter attached to the

wrong loop, there may be a fault in the wiring, the transmitter

may require an output trim, or the current meter may be mal-

functioning.

5.9 Calibration:

The scale is implemented by calibrating the transmitter. Trim func-

tion has several calibration functions. Smart transmitters operate

differently than analog transmitter. A smart transmitter uses a

microprocessor that contains information about the sensor's spe-

cific characteristics in response to pressure and temperature for

calculating the process variable. 4-20mA configuration sets the

ANGER: Explosion can result in death or serious

injury. Do not remove the transmitter covers in

xplosion-proof environments when the circuit is

powered. Both transmitter covers must be fully

ngaged to meet explosion-proof requirements.

DANGER: Electrical shock can result in serious

injury. When installing transmitters in close proxim-

ity of high voltage sources (near power lines) the

transmitter leads can be subject to high voltages.

Avoid contact with the leads and terminals.

Figure 17

1 2 ... 8 9 10 11 12 13 14 15 16

Comentários a estes Manuais

Sem comentários

Bosch FMC‑210‑DM manuels

Manuels d'utilisation et guides de l'utilisateur pour Sécurité Bosch FMC‑210‑DM.
Nous fournissons des manuels en pdf 1 Bosch FMC‑210‑DM à télécharger gratuitement par type de document : Manuel de l'utilisateur

Bosch FMC‑210‑DM Manuel de l'utilisateur (5 pages)

marque: Bosch | Catégorie: Safety | Taille: 1.23 MB |

Table des matières

FMC‑210‑DM Ручные извещатели

FMC-210-DM-H-B

FMC-210-DM-G-Y

FMC-210-EST-G-B

FMC-210-DM-G-R

FMM-KEY-Form G/H

Plus de produits et de manuels pour Sécurité Bosch

Modèles	Type de document
FDT 0000 A Front Door Transparent	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FDT 0000 A Front Door Transparent, 2 pages
FPP-5000-TI Trouble Interface for FPP-5000	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FPP-5000-TI Trouble Interface for FPP-5000, 3 pages
FAS‑ASD‑AR	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FAS‑ASD‑AR, 2 pages
HBE 0012 A Modular Extension Housing for 12 Module	Manuel de l'utilisateur Инструкция по эксплуатации Bosch HBE 0012 A Modular Extension Housing for 12 Modules, 2 pages
PSB 0004 A Power Supply	Manuel de l'utilisateur Инструкция по эксплуатации Bosch PSB 0004 A Power Supply, 2 pages
HMP 0003 A Mounting Plate for Mounting Frame	Manuel de l'utilisateur Инструкция по эксплуатации Bosch HMP 0003 A Mounting Plate for Mounting Frame, 2 pages
LSN 1500 A LSN improved Module 1500 mA	Manuel de l'utilisateur Инструкция по эксплуатации Bosch LSN 1500 A LSN improved Module 1500 mA, 4 pages
ANI 0016 A Annunciator Module	Manuel de l'utilisateur Инструкция по эксплуатации Bosch ANI 0016 A Annunciator Module, 2 pages
FLM-420-RHV Relay High Voltage Interface Modules	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FLM-420-RHV Relay High Voltage Interface Modules, 4 pages
THP 2020 A Thermal Printer	Manuel de l'utilisateur Инструкция по эксплуатации Bosch THP 2020 A Thermal Printer, 2 pages
IOS 0232 A RS232 Communication Module	Manuel de l'utilisateur Инструкция по эксплуатации Bosch IOS 0232 A RS232 Communication Module, 2 pages
FNM-320 Sounders Conventional	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FNM-320 Sounders Conventional, 4 pages
FCA‑500‑EU	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FCA‑500‑EU, 2 pages
FLM-420-NAC Signaling Device Interface Modules	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FLM-420-NAC Signaling Device Interface Modules, 4 pages
FMX-DET-MB	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FMX-DET-MB, 2 pages
Praesideo	Manuel de l'utilisateur Инструкция по эксплуатации Bosch Praesideo, 8 pages
FNM-420-A-BS Base Sounder, Indoor	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FNM-420-A-BS Base Sounder, Indoor, 4 pages
FNS‑420‑R LSN	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FNS‑420‑R LSN, 2 pages
FMH 0000 A	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FMH 0000 A, 2 pages
FDT 0002 A Large Front Door Transparent	Manuel de l'utilisateur Инструкция по эксплуатации Bosch FDT 0002 A Large Front Door Transparent, 2 pages

Sensor Electronics SEC 3100 Instruções de Operação Página 13

Comentários a estes Manuais

Bosch FMC‑210‑DM manuels

Bosch FMC‑210‑DM Manuel de l'utilisateur (5 pages)

Table des matières

Plus de produits et de manuels pour Sécurité Bosch